If spin speed ?0? is selected, the final spin is
CONSUMPTION DATAEND OF WASH CYCLE
cancelled, and the programme ends with a
The ?End? lamp of the programme sequence
Temperature SelectorLoadWaterEnergy Approx. Programmedrain cycle.
ProgrammeDurationindicator lights up.
(°C)(kg)(l)(kWh)(hours : minutes)START DELAY1. Press the ?On/Off? button to switch off the
Cotton955.060*1.852:05machine.
The ?Start Delay? button allows the user to run
Cotton605.0500.952:052. Turn the tap off.
the machine at his convenience, for example at
Cotton405.0500.602:05
night when electricity is cheaper.3. Wait for the lid to unlock (about 1 minute).
Daily Mixed403.0490.481:00
Select programme, spin speed and options.4. Open the lid and the drum doors and unload
Synthetic602.0560.801:30
Press the ?Start Delay? button several times to the machine. Leave the lid open for some time
Synthetic402.0560.451:20
select a delay time of 1, 3, 6, 9 or 12 hours. to allow the inside of the appliance to dry.
Delicate401.5600.600:45
The corresponding indicator lamp flashes.CHANGE THE PROGRAMME DURING
Wool401.0600.500:40
THE WASH CYCLE
Silk301.0600.300:50 Start the programme (see next paragraph).
Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized As the delay time decreases, the 1. Switch the appliance off by pressing ?On/
conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the corresponding indicator lamp flashes.
Off?.
values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
The data on the ?Energy Label? refer to the programme ?Cotton 60°C?. The flashing light of the delay indicator lamp 2. Turn the programme selector knob to the
* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains goes out when the programm starts.
new programme.
the water out.
The delay time can still be modified after the
?Rinse Hold? button3. Switch the appliance on again by pressing
PREPARATION OF WASH CYCLE
?Start? button has been pressed:
The laundry remains in the last rinse water ?On/Off?. The ?Start? button flashes. If
1. Load the machine, close the drum doors and To decrease the delay time
without progressing to the final spin cycle to necessary, select additional options and
check that they are properly locked.
avoid creasing and prevent colours from fading. (Repeatedly) press the ?Start Delay? button.different spin speed.
2. Add detergents and additives into the dispenser
This option is particularly recommended for the 4. Start programme by pressing the ?Start?
Note, however, that the selected wash
to no more than the ?MAX? level mark, as
?Synthetic?, ?Delicate? and ?Daily Mixed?
programme starts IMMEDIATELY as soon as you button.
follows:
programmes.
push ?Start Delay? with the ?1h? lamp flashing.
Programme with pre and main washPAUSE/INTERRUPT A PROGRAMME
This function is particularly useful if you want to
Main wash programme without prewashpostpone spinning to a later time, or if you want To increase the delay timeIf, for any reason, you wish to interrupt the
Fabric softeners and conditionersto drain only. Switch the washing machine off by pushing the programme for a certain time and continue it later:
Chlorine bleach As soon as the appliance stops in the rinse hold, ?On/Off? button.1. Press the ?On/Off? button.
the lamp of the ?Start? button flashes.
Stain remover agents Turn the programme selector to a different
2. After the desired pause, press again on the
Appliance in ?Rinse Hold?:programme.
Anti-scale agents (if necessary)?On/Off? button.
Press the ?Rinse Hold? button or the flashing
3. Press the ?On/Off? button. Switch the washing machine on again by
?Start? button: the programme will terminate CANCEL PROGRAMME
The lamp of the ?Start? button flashes.pressing the ?On/Off? button.
automatically with the selected spin cycle.
4. Turn the programme selector knob to the Reselect the desired programme and options. 1. Switch off the appliance by pressing ?On/Off?.
If you do not wish to spin the clothes, turn the
desired programme. The lamp of the Select the desired delay time by (repeatedly) 2. Turn the programme selector to ?Drain?.
programme?s standard spin speed lights up.programme selector knob to the ?Drain? pressing the ?Start Delay? button. Press the
programme and press the ?Start? button again.3. Switch the appliance on again by pressing
SELECT THE DESIRED OPTION?Start? button.?On/Off?. The lamp of the ?Start? button
?Intensive Rinse? button
flashes.
Selecting or deselecting an option can be done The amount of water is increased to ensure a PROGRAMME START
at any time during the programme. The option more intensive rinse.4. Press the ?Start? button to start the ?Drain?
Verify that the appliance is switched on.
will be applied as long as the corresponding programme.
This option is particularly suitable for areas with
Turn on the tap and press the ?Start? button.
programme phase has not been executed yet.
very soft water, washing baby linen and people
?Easy Ironing? buttonThe indicator lamp of the ?Start? button stops
with skin allergies.
flashing and lights up.
Can be used together with ?Cotton?, ?Synthetic?
Spin Speed selection button
and ?Daily Mixed? programmes to make ironing Note: If there is a power interruption or if the
Every programme has an automatically preset
easier.appliance is disconnected during the cycle, the
spin speed.
Increases the water quantity in rinsing and the programme will run again from the point where it
Press the button to set another spin speed.
clothes are spun in a softer manner.was interrupted.
5019 612 10076/A |